ohhh I see! How’d that sneaky little booger get there!! Argh!! Thanks so much!
Piston not running?
bobbles
#6
Enable tracing and then push the test button.
Do any of the IFS for time is between turn green.
The one for the current time should.
Alan_Lambert
#8
Is there something I could be missing? Do I need to enable it someplace? Turn it on or something?
bobbles
#9
When you create a piston, as soon as you save it, it becomes active. There is a button at the top which allows you to pause it. Have you paused it by mistake.
When you hit test, does one of the time ‘IFS’ turn green.
As I said above the piston works for me OK.
Alan_Lambert
#11
Before I hit test
Logs
12/21/2017, 11:24:10 AM +436ms
+0ms ╔Starting piston… (v0.2.100.20171211)
+395ms ║Subscribing to Sleeping.switch…
+726ms ╚Piston successfully started (725ms)
12/21/2017, 10:45:07 AM +571ms
+0ms ╔Starting piston… (v0.2.100.20171211)
+530ms ║Subscribing to Sleeping.switch…
+902ms ╚Piston successfully started (902ms)
12/21/2017, 10:28:19 AM +897ms
+1ms ╔Starting piston… (v0.2.100.20171211)
+608ms ║Subscribing to Sleeping.switch…
+1002ms ╚Piston successfully started (1001ms)
after I hit test - it ran… mode changed and I got email
Logs
12/21/2017, 11:31:00 AM +305ms
+1ms ╔Received event [Home].test = 1513873860305 with a delay of 0ms
+1876ms ╚Event processed successfully (1876ms)
12/21/2017, 11:24:10 AM +436ms
+0ms ╔Starting piston… (v0.2.100.20171211)
+395ms ║Subscribing to Sleeping.switch…
+726ms ╚Piston successfully started (725ms)
12/21/2017, 10:45:07 AM +571ms
+0ms ╔Starting piston… (v0.2.100.20171211)
+530ms ║Subscribing to Sleeping.switch…
+902ms ╚Piston successfully started (902ms)
12/21/2017, 10:28:19 AM +897ms
+1ms ╔Starting piston… (v0.2.100.20171211)
+608ms ║Subscribing to Sleeping.switch…
+1002ms ╚Piston successfully started (1001ms)
bobbles
#12
The trace button doesn’t appear until the piston has run. I imported your piston and put my devices into it. I pushed test and I got a notification and the trace button then appears. I’m not sure if you need to enable something somewhere to get the trace button. It’s been a while since I first started using this.
Alan_Lambert
#13
So if you import it… edit the last IF (its there for testing) to be 5 minutes in the future… save, test ( it will run)… does it run again in 5?
bobbles
#14
Well this is strange. It’s stopped working.
Earlier I changed the time for the day part to be in a current time range and it ran.
Changed the time for day again and it doesn’t run.
Also the test day isn’t working.
Will have to play.
Also with logging on full nothing is appearing in the logs when test is pressed.
EDIT : I had left it paused. 
bobbles
#15
OK. Tested again and got the notification when test button hit for the current time.
Set the day test to 5 min ahead and got that OK.
I’m using push notification not email.
Alan_Lambert
#16
This is gonna drive me crazy… I deleted the piston and reimported it… I get the same results… it only runs when I click test.
eibyer
#17
I only see one subscription (switch 14) and nothing else is going to trigger the time blocks except when the start time comes? (sorry, just jumping into this)
Alan_Lambert
#18
Im new enough to WC that Im not following about the subscription… but it sounds like you are own to something… What do you mean?
bobbles
#20
OK. What I had done in all my testing to get this to work was changing things to always subscribe. (Sorry for the late reply but it’s early evening in the UK).
You can see this by the + next to the statements.
You can either import this or just change yours.
If you remember earlier you changed yours from never subscribe to automatic. Change again to always.
